Search results

Good morning I have struggling to slow down the bed chains on a Teagle spreader. If I shut the speed down on the spreader control there is just a nasty loud hissing sound of the system seemingly fighting. The dials on the spools themselves seem to make little noticable difference. Would any...

Evening all Would anyone have an idea why the aircon might give off intermittently a sound like an air brake/valve blowing off. It does not do it all the time, definitely does not happen if aircon is off. Difficult to know from where it is coming. Thanks

Not agricultural but some possibly might find this interesting for the period equipment. It was filmed by my late Uncle.

Good afternoon Anyone in need of Highland spares. I would say 12ton machine from the 80s. The body is shot but the chains and gypsies are in fair order, including slats. No spinning deck. Tyres are 500/55 20 on 8 stud. Tyres have some perishing, not suitable for road use, centres in fair order.

My ploughing knowledge can be fitted on a postage stamp (if you can find one). I assume it is a Ransomes? Any ideas? Mouldboards look to be in fair order.

Hi all MF 135 with machine number: 135 4451** with FG below. Any ideas on possible age? Has under slung exhaust, MP and shell/round wings. Thanks

Will be sold by Cheffins, 20th April apparently.

Good evening. A couple of months ago I reverted to student mode (as pointed out by a very well respected Agric). I manged to rip off the trailer light socket from an LM435A. It seemed I had only pulled the wires out (along with other components). The wires come from the main loom into the 7 pin...

Just a heads up for Andrew Cross of A and R Handling nr Banbury, AKA @ACEngineering . I stupidly damaged my New Holland (Manitou based) telehandler with shear incompetence. I could not see from where the damaged pipe work had been ripped. Over the phone Andrew looked up the relevant area and...

Good morning Would like a value guesstimate on a 3 cylinder 35 for a neighbour. I would guess 1960-62 age, starts well and works bu tin work is quite scruffy. Thanks

http://journeytoforever.org/farm_library/medtest/medtest_hosier.html Depends on having dry land, but I thought this was interesting, particularly in light of the current push to sustainable farming.

Afternoon. I have a intermittent fault with the above. This morning 7th C range was allowing about 26.8mph on the dash. After 20 minutes of running the engine died a bit and the speed dropped of the dash. The engine picked up again but in top (C7) the engine would only rev to about 1600 with a...

Hi Do folk with working Collies take out veterinary insurance or is the cost prohibitive? If so, who with and what might be the expected premium. Thanks (actually asking for a family member)

Just wondering what people are paying (pm if preferred) for house and contents insurance. Say for a 4 to 5 bed house of modern-ish construction. I have been with the NFU for years and feel my leg coming slightly off the ground. Waiting for them to come back with a breakdown of the costs. Thanks

I cannot get this 4 cyl turbo engine to run. Changed lift pump and now has good prime to filter. Will also pump fuel out of the return to tank if union on injector pump is cracked. For some reason we did get it to run briefly and it stopped suddenly as if switched off. Discovered dead feed to...

Evening all A friend of mine, and I use the term loosely, is looking at an agreement with a Local Authority for using a small parcel of land for agricultural purposes. The agreement is set to run for 3 years with 12 month notice from either party. Are there any pitfalls with this kind of...

Good afternoon As above, I need to replace the spool valve control cables. One end is in the typical alloy cone arrangement, the lever end is held by a roll pin that catches an external detent that is crimped over the outer cable sheath. Thanks for any advice.

Good morning I had the error code E3 04 yesterday. I am struggling to find for what this belongs. Possibly PTO speed sensor? The buzzer was on continuously and the bale size disappeared. I was able to finish by ignoring, the baler seemed to work OK but had to be careful not to over size. I...

Just a few